加入收藏| 设为首页|English
86-0755-29785600
联系我们


0755-29785600

传真:0755-29785100

sale@yongerjia.com

产品展示 >> 返回 您当前所在位置:首页 > 产品展示 > 正文

5730 LED

  • 产品类型:贴片式发光管
  • 品牌:WEJ
  • 封装形式:5730
  • 型号(示例):WEJ5730
  • 产地:中国
  • 交货时间15天
  •      
  • 了解更多产品详情,您可以“查看联系方式或通过客服咨询”
发光颜色
Emitting color
波长范围(nm)
Wavelength(nm)
电压范围(v)
Forward Voltage(v)
亮度范围(mcd)
Luminous Intensity(mcd)
角度范围
Viewing Angle
Red 615-650 1.8-2.4 1500-6600 100-140
Orange 598-612 1.8-2.4 1500-6600 100-140
Yellow 584-596 1.8-2.4 1500-6600 100-140
Green 510-535 2.8-3.4 8000-12000 100-140
Bule 445-475 2.8-3.4 1500-5000 100-140
Purple 380-420 3.0-3.6 100-5000 100-140
White X:0.22-0.48
Y:0.22-0.48
2.8-3.4 6000-20000 100-140

1.Storage(储存)

☆Moisture proof and anti-electrostatic package with moisture absorbent material is used,to keep moisture to a minimum.Before opening the package, the product should be kept at 30℃ or less and humidity less than 60%RH,and be used whthin six months.
本产品使用密封防潮搞静电袋包装,并附有干燥剂,以保证产品不会吸潮,产品包装在开封前,产品须放在温度不高于30℃,湿度不高于60%RH的环境中。
☆After opening the package,the product should be stored at 30℃or less and humidity less than 10%RH,and be soldered within 24 hours.It is recommended that the product be operated at the workshop condition of 30℃or less and humidity less than 60%RH.
产品包装开封后,产品必须储存在温度不高于30℃,湿度不高于10%RH的环境中,且应该在24小时内使用完,建议工作环境为温度不高于30℃,湿度不高于60%RH。
☆If the moisture absorbent material has fade away or the LEDs have exceeded the storage time,baking treatment should be performed based on the following condition(75±5) ℃ for 24 hour.
对于尚未焊接的LED,如果吸湿材料或包装失效,或者产品没有符合以上有效储存条件,烘烤可以起到一定的性能恢复效果,烘烤条件:75±5 ℃,持续24小时。

2.Static electricity(静电防护)
☆Static electricity or surge voltage damages the LEDs.Damaged LEDs will show some unusual characteristic such as the forward voltage gecomes lower,or the LEDs do not light at the low current.even not light.All devices,equipment and machinery must be properly grounded.At the same time,it is recommended that wrist bands or anti-electrostatic gloves,anti-electrostatic containers be used when dealing with the LEDs.
静电或电涌会导致产品特性发生改变,例如正向电压降低,如果情况严重甚至会损毁产品,所以在使用时必须采取有效的防静电措施;所有相关的设备和机器都应该正确接地,同时必须采取其他防止静电和电涌的措施,使用静电手环,防静电垫子,防静电工作服,工作鞋,手套,防静电容器,都是有效的防止静电和电涌的措施。

文件名文件类型说明下载区